高摩擦性能碳／碳复合材料的微观结构

使用激光拉曼探针和电子显微术对试样的断裂面和薄膜样品观察及电子衍射技术研究了两种抗摩擦性能相差悬殊的碳／碳复合材料的微观结构，发现两种材料的微观结构在石墨晶体的结晶结构完整性和取得性以及纤维和基体间的界面行为上有显著差异。     

侧压式进气道内部阻力分析

针对目前对超燃冲压发动机阻力特性的需要,以侧压式进气道为例,分别以内壁面和捕获流管为分析体,对其内部阻力进行分类;以数值模拟为手段,给出了总阻力的大小及各项阻力的分配比例,并分析了进气道几何参数变化对阻力的影响关系。     

金属橡胶减振器在发动机安装时的减振设计研究

通过理论和试验研究,介绍了采用金属橡胶减振器减小飞机由发动机引起的结构振动问题。     

一种直升机粘弹减摆器时域模型参数识别方法

在时域内建立了直升机粘弹减摆器的非线性模型。该模型基于不可逆热力学原理，在线性滞弹性位移场(Anelastic displacement fields，ADFs)模型的基础上，通过一组材料状态变量函数引入了粘弹性材料的非线性特性；文中以硅橡胶为研究对象，在粘弹减摆器实际工作中比较典型的幅值和频率范围内，进行了简谐实验，并通过两位移幅值(0．1cm，0．6cm)的应变／应力滞迟回线直接进行模型参数识别。最后，通过与线化复模量、不同幅值的应变／应力的滞迟回线等实验数据比较，证实了本文模型具有较好的可靠性，为进一步研究直升机粘弹减摆器的性能和带减摆器的旋翼气弹分析奠定了基础。     

Nutation instability of spinning solid rocket motor spacecraft

The variation of mass,and moment of inertia of a spin-stabilized spacecraft leads to concern about the nutation instability.Here a careful analysis on the nutation instability is performed on a spacecraft propelled by solid rocket booster (SRB).The influences of specific solid propellant designs on transversal angular velocity are discussed.The results show that the typical SRB of End Burn suppresses the non-principal axial angular velocity.On the contrary,the frequently used SRB of Radial Burn could amplify the transversal angular velocity.The nutation instability caused by a design of Radial Burn could be remedied by the addition of End Burn at the same time based on the study of the combination design of both End Burn and Radial Burn.The analysis of the results proposes the design conception of how to control the nutation motion.The method is suitable to resolve the nutation instability of solid rocket motor with complex propellant patterns.     

Laminar flow control research at TsAGI: Past and present

This paper presents a brief review of activities in laminar flow control being performed at the Central Aerohydrodynamic Institute named after Prof. N.E. Zhukovsky (TsAGI). These efforts are focused on the improvement of the existing laminar flow control methods and on the development of new ones. The investigations have demonstrated the effectiveness of aircraft surface laminarization applications with the aim of friction drag reduction. The opportunity of considerable delaying of laminar-turbulent transition due to special wing profile geometry and using boundary layer suction and surface cooling has been verified at sub- and supersonic speeds through various wind tunnel testing at TsAGI and during flying laboratory experiments at the Flight Research Institute (LII). The investigations on using hybrid laminar flow control systems for friction drag reduction were also carried out. New techniques of laminar flow control were proposed, in particular, the method of local heating of the wing leading edge, boundary layer laminarization by means of receptivity control, and electrohydrodynamic methods of boundary layer stability control.     

C/C素坯密度对GSIC/C-SiC复合材料摩擦磨损性能的影响

采用气相渗硅工艺(GSI)制备C/C-Si C复合材料,研究了C/C素坯密度对GSI C/C-Si C复合材料物相组成与摩擦磨损性能的影响,分析了C/C-Si C复合材料的制动过程,并归纳了其摩擦磨损机理。结果表明,随着C/C素坯密度的增大,GSI C/C-Si C复合材料的密度呈递减趋势,且C含量和开气孔率逐渐增加,而Si C含量和残余Si含量逐渐减少;自对偶条件下,复合材料的平均摩擦系数、磨损率均呈现先增大后减小的趋势,当C/C素坯密度为1.25g/cm3时有最大值,而制动稳定系数则不断增大。GSI C/C-Si C复合材料的制动过程是犁沟效应和粘着效应共同作用的结果,制动初始阶段和刹停阶段以犁沟效应为主,中间阶段以粘着效应为主。     

2219铝合金搅拌摩擦焊缝Al2Cu相聚集行为特征分析

对2219C10S状态铝合金进行搅拌摩擦焊接试验,发现焊缝中存在聚集物的异常聚集现象,聚集相在X光检测中显示为亮白色聚集物,主要形态分为团块状、线状和指状三种,聚集相处焊缝的力学性能与无聚集相焊缝的力学性能基本相同。各形态聚集相的分布位置受搅拌头焊接影响区域的不同而不同,团块状聚集相主要存在于焊核中心或偏焊缝上表面位置处,线状和指状聚集相主要存在于焊核中心或偏焊缝根部位置处。对异常聚集相进行能谱分析知,聚集相主要组成元素为Al和Cu,原子百分比近似为2∶1,确定聚集相主要成分为Al2Cu。对聚集相的成因进行分析认为,聚集相的产生主要受搅拌摩擦焊接热输入及搅拌头机械搅拌作用的影响,在焊接过程中,塑态软化金属中的Al2Cu在填补搅拌针后方空腔的过程中出现了聚集行为,随着塑态金属的凝固,聚集行为开始变得缓慢并结束。     

2219铝合金变截面结构搅拌摩擦焊接工艺及组织特性

针对变截面结构产品,提出了一种变截面搭接结构搅拌摩擦焊接方法,通过加装辅助板将整条焊缝焊接方向上补偿为等厚度。焊接采用一次定位焊接+二次定位焊接+正式焊接的工艺方式,一次定位焊为预定位,二次定位焊保证辅助板与试片主体结构之间形成有效连接,正式焊保证形成完整的焊缝。焊缝表面成形良好,超声相控阵检测无超标缺陷。通过对力学性能的分析,变截面搭接结构处焊缝与非搭接处焊缝和常规对接焊缝的力学性能基本相同,平均抗拉强度均达到母材的70%以上,平均延伸率均在5.8%以上。变截面搭接焊缝焊核处晶粒形态为细小的等轴晶,靠近轴肩影响区部分的晶粒尺寸大于靠近焊缝根部的晶粒尺寸,受再结晶影响,焊缝两侧热机影响区处辅助板搭接界面消失。